EN
AR
CS
DA
NL
FI
FR
DE
EL
IT
JA
KO
NO
PL
PT
RO
RU
ES
TL
ID
SK
SL
UK
VI
TH
TR
AF
MS
SW
GA
CY
BE
KA
LO
LA
MI
MR
MN
NE
UZ
- ພາບລວມ
- ການສອບຖາມ
- ຜະລິດຕະພັນທີ່ກ່ຽວຂ້ອງ
ຜະລິດຕະພັນລາຍລະອຽດ
The upper part has a protective ring and a pipeline valve system. The middle bottle body has a stainless steel shell and a heat insulating layer. Inside there is a stainless steel liner and a vacuum interlayer.
Supercharger: The supercharger adopts a finned heat exchanger and is installed at the bottom of the bottle to increase the pressure in the bottle. However, when the liquid level in the bottle is low, the boosting speed is very slow. Therefore, it is recommended that the user Before use, increase the pressure inside the bottle so that the pressure inside the bottle can meet the requirements when using the liquid.
Discharge valve: This valve is connected to the gas phase space of the gas cylinder. Open this valve to release the gas in the cylinder to reduce the pressure.
Inlet shut-off valve: This valve is used to control the filling of cryogenic liquid.
Liquid outlet valve: This valve is used to control the output of cryogenic liquid.
Booster cut-off valve: This valve is used to control the booster circuit, open the valve to pressurize the bottle.
Boost regulating valve: The cryogenic liquid enters the supercharger through this valve and turns into gas, and returns to the inner tank, so that the pressure in the bottle reaches the set value of the boost regulating valve.
Liquid level gauge: The liquid level gauge adopts a capacitive liquid level gauge. The capacitive sensor generates a proportional electrical signal according to the height of the liquid in the bottle. The liquid level display table converts the signal after receiving the electrical signal, and expresses different liquids in percentage numbers. ປະລິມານ.
Protection of the enclosure under overpressure conditions is achieved by a vacuum plug. If the liner leaks (resulting in super high sandwich pressure), the vacuum plug will open to release the pressure. In the event of a leak from the vacuum plug, the interlayer vacuum will be broken, at which point the housing will be found to "sweat" and frost. Of course, frost or condensation on the end of the tubing connected to the bottle is normal.
Vacuum plug: Protection of the housing under overpressure conditions is achieved by a vacuum plug. If the liner leaks (resulting in super high sandwich pressure), the vacuum plug will open to release the pressure. In case of leakage of the vacuum plug, the vacuum of the interlayer will be broken. At this time, "sweating" and frosting of the shell can be found. Of course, frost or condensation on the end of the tubing connected to the bottle is normal. (Warning: Do not pull out the vacuum plug under any circumstances)
Liquid supply and use process of Dewar bottle
First, make sure that the main pipeline valve of the spare cylinder group has been closed, open the gas valve and liquid outlet valve on the steel cylinder to be used, then open the corresponding valve on the header skid of the cylinder group connected to the steel cylinder, and then open the corresponding pipeline main valve. ປ່ຽງ. Finally, open the valve at the inlet of the vaporizer, and the liquid will be vaporized by the vaporizer and supplied to the user after being regulated by the pressure regulator. When supplying liquid, if the pressure of the steel cylinder is not enough, you can open the booster valve of the steel cylinder, and pressurize the steel cylinder through the booster system of the steel cylinder, so as to obtain sufficient liquid supply pressure.
Cryogenic Liquid Cylinder Storage Tank For Medical Use Dewar
-They are widely used in nitrogen storage, for Welding ,laser cutting, for Cryosauna...
-For Oxygen storage,for farming,for Hospital oxygen supply .....
-for LCO2 storage,widely use in food freezing, for beer factory….
For LNG supply, widely use in community LNG supply system…
ການຫຸ້ມຫໍ່ແລະການຈັດສົ່ງ
FAQ
FAQ 1. MOQ ແມ່ນຫຍັງ? A: ຈາກຫນຶ່ງກະບອກ 2. ເວລາການຈັດສົ່ງແມ່ນຫຍັງ? A: 7-10 ມື້ Exwork ຫຼັງຈາກທີ່ພວກເຮົາໄດ້ຮັບເງິນຝາກ, ຫຼັງຈາກທີ່ພວກເຮົາສັ່ງຊື້ເຮືອຫຼືການຂົນສົ່ງທາງອາກາດ, ພວກເຮົາສາມາດຮູ້ເວລາທັງຫມົດທີ່ຈະເຮັດການຈັດສົ່ງກັບປະເທດຂອງລູກຄ້າ. 3. ກວດສອບຄຸນນະພາບກ໊າຊແນວໃດ? A: ກ່ອນອື່ນ, ທີມງານຂອງພວກເຮົາຈະເຮັດການປິ່ນປົວກະບອກ (ທໍາຄວາມສະອາດ, ຕາກແຫ້ງ, ສູນຍາກາດ, ສູບນ້ໍາ, ແລະການທົດແທນກ່ອນທີ່ຈະຕື່ມອາຍແກັສເພື່ອຮັບປະກັນວ່າກະບອກສູບພາຍໃນແມ່ນສະອາດແລະແຫ້ງ) ອັນທີສອງ, ພວກເຮົາຈະທົດສອບກະບອກສູບທີ່ໄດ້ຮັບການປິ່ນປົວອີກເທື່ອຫນຶ່ງ, ໃຫ້ແນ່ໃຈວ່າກະບອກສູບຢູ່ໃນນັ້ນ. ແມ່ນສະອາດແລະແຫ້ງ. ອັນທີສາມ, ພວກເຮົາຈະວິເຄາະອາຍແກັສຫຼັງຈາກຕື່ມເຂົ້າໄປໃນກະບອກສູບແລະສະຫນອງ COA (ໃບຢັ້ງຢືນການວິເຄາະ) 4. ຖັງທັງຫມົດສາມາດເອົາມາໃຊ້ຄືນໃຫມ່ໄດ້ບໍ? A: ປົກກະຕິແລ້ວຊີວິດການເຮັດວຽກຂອງກະບອກເຫຼັກ seamless ແມ່ນຫຼາຍກ່ວາ 20 ປີ, ທໍ່ຖິ້ມສາມາດຖືກນໍາໃຊ້ພຽງແຕ່ຫນຶ່ງຄັ້ງ. 5. ພວກເຮົາສາມາດສົ່ງກະບອກສູບກັບຄືນໄປຈີນແລະຕື່ມແກັດບໍ? A: ແມ່ນແລ້ວ, ເມື່ອບໍລິສັດຂອງທ່ານໝົດອາຍແກັສ, ທ່ານສາມາດສົ່ງກະບອກເປົ່າ ແລະ ຕື່ມກ໊າຊຄືນໄດ້. ທ່ານພຽງແຕ່ຕ້ອງການແຈ້ງໃຫ້ພວກເຮົາກ່ອນການສົ່ງອອກຂອງທ່ານ, ພວກເຮົາຈະຈັດການກັບການເກັບພາສີຂອງຖັງໃນປະເທດຈີນ. 6. ມາດຕະຖານ Cylinders ແລະ Valve ທີ່ມີຢູ່ A: Cylinder DOT-3AA ISO9809, GB5099, TC-3AAM. EN1964, KGS ວາວ: DISS, CGA, DIN, BS, AFNOR, JIS. 7. ຂ້ອຍສາມາດເຮັດ LCL ກັບສິນຄ້າທົ່ວໄປອື່ນໆຂອງຂ້ອຍໄດ້ບໍ? A: ຜະລິດຕະພັນຂອງພວກເຮົາເປັນສິນຄ້າ DG ລະດັບ 2.2 ແລະຄວນຈະສົ່ງກັບສິນຄ້າ DG, ຖ້າການຂົນສົ່ງເປັນສິນຄ້າທົ່ວໄປ, ມັນຜິດກົດຫມາຍ, ພວກເຮົາຄວນສັ່ງສິນຄ້າ DG ຈາກບໍລິສັດຂົນສົ່ງ, ຖ້າທ່ານມີຜະລິດຕະພັນທົ່ວໄປອື່ນໆ, ທ່ານສາມາດໃສ່ໃນການຂົນສົ່ງແລະ ສົ່ງເປັນສິນຄ້າ DG.
ຄຸນນະພາບ
ເປັນຫຍັງເລືອກເລົາ
ກ່ຽວກັບພວກເຮົາ
